Neue HAMLAB in den USA und TUNE (RF Power) Problem

Red Pitaya SDR-Transceiver
rick-n1gp
Beiträge: 3
Registriert: 03 Feb 2017, 17:51

Neue HAMLAB in den USA und TUNE (RF Power) Problem

Beitragvon rick-n1gp » 17 Feb 2017, 16:57

Grüße aus New Hampshire, USA.

Bitte vergib mir mein Deutsch, ich benutze Google Translate.

Ich erhielt schließlich mein HAMlab und es kam in großartiger Form an.
Ich bin sehr beeindruckt von der Qualität der Konstruktion.

Ich habe die Anweisungen befolgt:
Http://hamlabdoc.readthedocs.io/de/latest/

Und haben die Hardware und die installierte PowerSDR Charly25 / HAMlab erfolgreich eingerichtet.

So weit in meiner Prüfung möchte ich die "TUNE" -Funktion zu sehen, RF-Strom aus zu überprüfen
Mein 100Watt Power / SWR Meter und eine 50 Ohm Dummy Last.

Ich sehe nur HF-Leistung ~ 10 Watt, wenn in CWU oder CWL-Modus, wird nichts ausgegeben
In jedem anderen Modus (LSB, USB, AM, FM).

Auch die Leistung scheint nicht mit dem "DRIVE" Schieberegler einstellbar, es ist alles
ON bei 10 Watt oder alle aus 0 Watt. Nein dazwischen.

Receive ist gut und es ist sehr schön mit dem Dämpfungsglied / Preamp Selektionen.

Irgendwelche Hinweise, was ich tun kann, falsch auf der "TUNE" Schieberegler HF-Energie Probleme?

Vielen Dank,

-Rick / N1GP
Benutzeravatar
Egbert
Beiträge: 8
Registriert: 10 Mär 2016, 20:18

Re: Neue HAMLAB in den USA und TUNE (RF Power) Problem

Beitragvon Egbert » 17 Feb 2017, 21:44

Hi Rick.

Tune button works in CW, but you must set the Monitor button on.

It also Enables the Sidetone , SDR works only when there is Audio... ;)

Under Setup / Transmit you can set the Tune power value and also
the meter settings for Fwd/Rev/ or SWR.

In my RedPitaya Setup i can use the Drive slider, but i am not shure
i you can do so...

In SSB mode the Output is set with the PC Souncard LineOut slider...

I use a modified version of openHP SDR and i can set the Power with
the Drive Slider...


73's Egbert PAØEJH.
Dateianhänge
Hamlab.png
rick-n1gp
Beiträge: 3
Registriert: 03 Feb 2017, 17:51

Re: Neue HAMLAB in den USA und TUNE (RF Power) Problem

Beitragvon rick-n1gp » 20 Feb 2017, 14:28

Hi Egbert,

Tnx for your reply and information.

I did try and have all those things you mentioned but still I cannot
adjust the driver power.

I sent redpitaya support an email and they replied that it is a known bug.

I am going to send them another email because I notice they have the
source code checked in to github (look at the bottom of the page):
http://hamlabdoc.readthedocs.io/en/latest/appsFeatures/appSDR.html?highlight=github

But that repository contains no changes from RP only a fork from openHPSDR version.

I wonder where you got your version of Powersdr, Did you modify it yourself?

-Rick / N1GP
Benutzeravatar
Egbert
Beiträge: 8
Registriert: 10 Mär 2016, 20:18

Re: Neue HAMLAB in den USA und TUNE (RF Power) Problem

Beitragvon Egbert » 20 Feb 2017, 17:02

Hi Rick.

I use only the RedPitaya, and i made my own Setup, see my QRZ page....

But i dont know all the hardware in the Hamlab, i heard that they use a Spinoff from the ALEX Board, and they ommit the bandPass filters.
There is a AudioBoard, but we dont know exactly what type of Board, and the Documentation i read is very limited....

But it is very importand that you save every change you make, save it in the Transmit profile you use, otherwise it it will be forgotten in the software.

If you can figure out what Hardware you have, perhaps you can use the Software on this Forum...

I use the version openHPSDR version 3.3.9 with am Mod from this Forum, and there also a Topic about a AudioBoard....

But there is a catch, we use the Image from PavelDemin, and i think you have different version in your HamLab...

But PA3ANG has also a HamLab, he has a lot of troubles, from a suddenly dead RedPitaya to the same problems as you have...

You can contact him via his HomePage https://pa3ang.nl/archives/category/red-pitaya

73's Egbert PAØEJH.
rick-n1gp
Beiträge: 3
Registriert: 03 Feb 2017, 17:51

Re: Neue HAMLAB in den USA und TUNE (RF Power) Problem

Beitragvon rick-n1gp » 25 Feb 2017, 23:18

Hello Egbert,

I really enjoyed your projects as viewed on your QRZ web page.

That is a very nice all-in-one SDR transceiver based on the RP.
I wish the FET-50PA kit was available to USA, the 28v boosters
are readily available on Ebay. It makes for a nice 50W PA?

The RP support has been very helpful and I hope to get involved with them
to help.

Best 73's

-Rick / N1GP

Zurück zu „HAMLAB“

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 1 Gast