Red Pitaya Hardware Specifications V1.1.1
Verfasst: Mi Mär 02, 2016 5:47 pm
Red Pitaya Hardware Specifications V1.1.1
Product name: Red Pitaya, model V1.1
RF inputs
Number of channels: 2
Bandwidth: 50 MHz (3 dB)
Sample rate: 125 Msps
ADC resolution 14 bits
Input coupling: DC
Input noise level: < 119 dBm /Hz (D)
Input impedance: 1 M? // 10 pF (A,B)
Full scale voltage: 2Vpp, (46 Vpp for lowgain jumper setting) (T,V)
DC offset error: <5 % FS (G)
gain error: < 3% (at high gain jumper setting), <10% (at low gain jumper setting) (G)
Absolute maximum input voltage rating: 30 V (S) (1500 V ESD)
Overload protection: protection diodes (under the input voltage rating conditions)
Input channel isolation: typical performance 65 dB @ 10 kHz, 50 dB @ 100 kHz, 55 dB @ 1 M, 55 dB @ 10 MHz, 52 dB @ 20 MHz, 48 dB @ 30 MHz, 44 dB @ 40 MHz, 40 dB @ 50 MHz. (C)
Harmonics
at 3 dBFS: typical performance <45 dBc (E)
at 20 dBFS: typical performance <60 dBc (E)
Spurious frequency components: Typically <90 dBFS (F)
Connector type: SMA (U)
Frequency response is adjusted by digital compensation
RF outputs
Number of channels: 2
Bandwidth: 50 MHz (3 dB) (K)
Sample rate: 125 Msps
DAC resolution: 14 bits
Output coupling: DC
Load impedance: 50 ? (J)
Output slew rate limit: 200 V/us
Connector type: SMA (U)
DC offset error: < 5% FS (G)
Gain error: < 5% (G)
Full scale power: > 9 dBm (L)
Harmonics: typical performance: (at 8 dBm)
51 dBc @ 1 MHz
49 dBc @ 10 MHz
48 dBc @ 20 MHz
53 dBc @ 45 MHz
Auxiliary analog input channels:
Number of channels: 4
Nominal sampling rate: 100 ksps (H)
ADC resolution 12 bits
Connector: dedicated pins on IDC connector E2 (pins 13,14,15,16)
Input voltage range: 0 to +3.5 V
Input coupling: DC
Auxiliary analog output channels
Number of channels: 4
Output type: Low pass filtered PWM (I)
PWM time resolution: 4ns (1/250 MHz)
Connector: dedicated pins on IDC connector E2 (pins 17,18,19,20)
Output voltage range: 0 to +1.8 V
Output coupling: DC
General purpose digital input/output channels: (N)
Number of digital input/output pins: 16
Voltage level: 3.3 V
Direction: configurable
Location: IDC connector E1 (pins 324 )
Extension:
Connector: 2 x 26 pins IDC (M)
Power supply:
Available voltages: +5V, +3.3V, 3.3V
Current limitations: 500 mA for +5V and +3.3V (to be shared between extension module and USB devices), 50 mA for 3.3V supply.
Serial connectivity:
Connector type: 2x “SATA type” connector
Two differential pairs per connector enabling up to 500 Mbps
CPU / FPGA: Xilinx Zynq 7010 SoC
17,600 LUTs
28k Logic Cells
80 DSP slices
Dual ARM® Cortex™A9
Memory: 4 Gb DDR3 SDRAM (512 MB)
SD card:
Card type: micro SD
Supported standard: SD/SDIO 2.0/MMC3.31
File System: FAT32 (255 heads, 63 sectors)
Maximum card size: 32 GB (tested with: Apacer microSD HC 4GB Class 4 and others)
WiFi:
WiFi USB dongles: tested with Edimax EW7811Un
Fan: Optional fan power supply (5V)
Power supply: (O)
Voltage: 5 V
Current: 2 A
Connector type: micro USB
Compliant with relevant regulation standards
Recommended power supply: HNP10ImicroUSB
Dimensions: 107 mm x 60 mm x 21 mm (W)
Power consumption: typically < 0.9 A @ 5V (P)
Environmental conditions:
Temperature:
Minimum ambient operating temperature: 5 °C
Maximum ambient operating temperature: 30 °C (P)
Storage temperature range from 50 °C to 150 °C
Laboratory ambient temperature range: 22 °C ± 2 °C (R)
Exposed surface temperature: < 70 °C (Q)
Maximum Zynq SoC IC operation temperature: 85 °C
Humidity: 15 % 85 % (non condensing)
Product name: Red Pitaya, model V1.1
RF inputs
Number of channels: 2
Bandwidth: 50 MHz (3 dB)
Sample rate: 125 Msps
ADC resolution 14 bits
Input coupling: DC
Input noise level: < 119 dBm /Hz (D)
Input impedance: 1 M? // 10 pF (A,B)
Full scale voltage: 2Vpp, (46 Vpp for lowgain jumper setting) (T,V)
DC offset error: <5 % FS (G)
gain error: < 3% (at high gain jumper setting), <10% (at low gain jumper setting) (G)
Absolute maximum input voltage rating: 30 V (S) (1500 V ESD)
Overload protection: protection diodes (under the input voltage rating conditions)
Input channel isolation: typical performance 65 dB @ 10 kHz, 50 dB @ 100 kHz, 55 dB @ 1 M, 55 dB @ 10 MHz, 52 dB @ 20 MHz, 48 dB @ 30 MHz, 44 dB @ 40 MHz, 40 dB @ 50 MHz. (C)
Harmonics
at 3 dBFS: typical performance <45 dBc (E)
at 20 dBFS: typical performance <60 dBc (E)
Spurious frequency components: Typically <90 dBFS (F)
Connector type: SMA (U)
Frequency response is adjusted by digital compensation
RF outputs
Number of channels: 2
Bandwidth: 50 MHz (3 dB) (K)
Sample rate: 125 Msps
DAC resolution: 14 bits
Output coupling: DC
Load impedance: 50 ? (J)
Output slew rate limit: 200 V/us
Connector type: SMA (U)
DC offset error: < 5% FS (G)
Gain error: < 5% (G)
Full scale power: > 9 dBm (L)
Harmonics: typical performance: (at 8 dBm)
51 dBc @ 1 MHz
49 dBc @ 10 MHz
48 dBc @ 20 MHz
53 dBc @ 45 MHz
Auxiliary analog input channels:
Number of channels: 4
Nominal sampling rate: 100 ksps (H)
ADC resolution 12 bits
Connector: dedicated pins on IDC connector E2 (pins 13,14,15,16)
Input voltage range: 0 to +3.5 V
Input coupling: DC
Auxiliary analog output channels
Number of channels: 4
Output type: Low pass filtered PWM (I)
PWM time resolution: 4ns (1/250 MHz)
Connector: dedicated pins on IDC connector E2 (pins 17,18,19,20)
Output voltage range: 0 to +1.8 V
Output coupling: DC
General purpose digital input/output channels: (N)
Number of digital input/output pins: 16
Voltage level: 3.3 V
Direction: configurable
Location: IDC connector E1 (pins 324 )
Extension:
Connector: 2 x 26 pins IDC (M)
Power supply:
Available voltages: +5V, +3.3V, 3.3V
Current limitations: 500 mA for +5V and +3.3V (to be shared between extension module and USB devices), 50 mA for 3.3V supply.
Serial connectivity:
Connector type: 2x “SATA type” connector
Two differential pairs per connector enabling up to 500 Mbps
CPU / FPGA: Xilinx Zynq 7010 SoC
17,600 LUTs
28k Logic Cells
80 DSP slices
Dual ARM® Cortex™A9
Memory: 4 Gb DDR3 SDRAM (512 MB)
SD card:
Card type: micro SD
Supported standard: SD/SDIO 2.0/MMC3.31
File System: FAT32 (255 heads, 63 sectors)
Maximum card size: 32 GB (tested with: Apacer microSD HC 4GB Class 4 and others)
WiFi:
WiFi USB dongles: tested with Edimax EW7811Un
Fan: Optional fan power supply (5V)
Power supply: (O)
Voltage: 5 V
Current: 2 A
Connector type: micro USB
Compliant with relevant regulation standards
Recommended power supply: HNP10ImicroUSB
Dimensions: 107 mm x 60 mm x 21 mm (W)
Power consumption: typically < 0.9 A @ 5V (P)
Environmental conditions:
Temperature:
Minimum ambient operating temperature: 5 °C
Maximum ambient operating temperature: 30 °C (P)
Storage temperature range from 50 °C to 150 °C
Laboratory ambient temperature range: 22 °C ± 2 °C (R)
Exposed surface temperature: < 70 °C (Q)
Maximum Zynq SoC IC operation temperature: 85 °C
Humidity: 15 % 85 % (non condensing)